CD423-AA-000 AC Servo Driver

£226.32 £188.60
In stock 1 in stock. - If not in stock expect about 14-21 days
SKU
CD423-AA-000

The CD423-AA-000 AC servo driver can be used with motors up to 750W.


Frequently bought together

  1. CD423-AA-000 AC Servo Driver
  2. +
  3. T-75R-100-(use with CD420, CD422, FD422. 75Ω, 100W)
  4. +
  5. SMC60S-0020-30MAK-3LKU
  6. +
  7. SMC60S-0040-30MAK-3LKU
Total price: £0.00

 

Technical Parameters

 

Main supply voltage 200-240VAC±10% 50/60Hz±3HZ 0.5A
Control circuit voltage 200-240VAC±10% 50/60Hz±3HZ (750W,5.5A),(200W,1.5A)
Rated current(RMS) 4A
Peak current(PEAK) 15A
Feedback signal Single coil 17-bit magnetic encoder
Single coil 20-bit communication encoders
Multi-turn 16-bit communication type absolute encoder
Brake chopper Built-in braking resistor 100 Europe, limit power 10W; if the actual power exceed 10W, Need use an external braking resistor according to application, mainly in occasion of quick stop and start
Brake chopper threshold DC380V±5V
Over-voltage alarming threshold DC400V±5V
Under-voltage alarming threshold DC200V±5V
Cooling method Forced air cooling
Weight(Kg) 0.8
Digital input specification 7 digital inputs, with COMI terminal for PNP (high-level valid 12.5-30V) or NPN (low level valid) connection.
Digital input function Define freely according to requirement, supporting following functions: Driver enable, driver fault reset, driver mode control, proportional control, positive limit, negative limit, homing signal, reverse command, internal speed section control, internal positive section control, quick stop, start homing, active command, switch electronic gear ratio, switch gain
Digital output specification 5 digital outputs, OUT1~OUT4 current is 100mA, BR+/BR- (Brake control output ) current is 500mA, can drive brake device directly
Digital output function Define freely according to pre-requirement, supporting following functions: Driver ready, driver fault, position reached, motor at zero speed, motor brake, motor speed reached, Z signal, the maximum speed obtained in torque mode, motor brake, position limiting, reference found, multi-position reached.
Analog input 2 analog input, can be used to control speed and torque, the input range is -10V~10V.Output encoder signal is optional, can be used in the multiple axises synchronization, the max.
Communication interface RS232(use RJ45 network port to connect with the PC)
Protection functions Over-voltage protection,under-voltage protection,motor over-heat protection(IT),short-circuit protection,drive over-heat protection,etc.
Operating temperature 0~40℃
Storage temperature -10℃~70℃
Humidity(non-condensing) Below 90%RH
Protection class IP20
Installation environment Installed in a dust-free, dry and lockable environment(such as in an electrical cabinet)
Installation mode Vertical installation
Height No power limitation below 1000m
Atmospheric pressure 86kpa~106kpa

Position control mode

 

Maximum input pulse frequency Differential transmission mode: 4MPPS
Open collector transmission mode:200KPPS
Pulse command mode Pulse+Direction ,CCW+CW , A phase+B phase(5V-24V)
Command smoothing mode Low pass filter(Set by internal parameters)
Feedforward gain Set by internal parameters
Electronic gear ratio Setting range Gear factor:-32768~32767,Gear divider:1~32767
Position loop sampling frequency 1KHz

 

Velocity control mode

 

The range of analog input voltage -10~+10V(resolution is 12bits)
Input resistance 200K
Analog input sampling frequency 4KHz
Command control mode External analog command/Internal analog instructions
Command smoothing mode Low pass filter(Set by internal parameters)
Dead zone of input voltage setting Set by internal parameters
Offset of input voltage setting Set by internal parameters
Limit of speed Set by internal parameters
Limit of torque Set by internal parameters
Velocity loop sampling frequency 4KHz

 

Torque control mode

 

The range of analog input voltage -10~+10V(resolution is 12bits)
Input resistance 200K
Input sampling frequency 4KHz
Command control mode External analog command/Internal analog instructions
Command smoothing mode Low pass filter(Set by internal parameters)
Limit of speed Set by internal parameters
Dead zone of input voltage setting Set by internal parameters
Offset of input voltage setting Set by internal parameters
Mechanical dimensions
Current loop sampling frequency 16KHz

 

Mechanical dimensions

More Information
Manufacturer Kinco
EAN Number No
Write Your Own Review
Only registered users can write reviews. Please, Sign in or create an account